1 Opening(s)
9.0 Year(s) To 20.0 Year(s)
Not Disclosed by Recruiter
Qualification: Diploma / B.E in Electrical, Electronic or InstrumentationExperience: Min 10 to 20 Yrs. in foundry industries / Sand Plant.Work location: Bhosari in Pune
Computer Literacy: Working experience in SAP, Word, Excel, PowerPoint etc.Preferred Candidate: Local area PCMC or nearby candidate with SAP knowledge with complying above requirement.Skills Required: Good Communication Skills, ...
1 Opening(s)
10.0 Year(s) To 15.0 Year(s)
Not Disclosed by Recruiter
This position will have the overall accountability to:
• Ensure that Production shift Incharge has experience in Blow moulding machines (like Uniloy, Bestar, Tongda, Jagmohan, IBM Victor & CMP machines).Be the dedicated formulation expert.
Machine process set-up, minimize rejection/wastage and max. Capacity utilization of machines.
• Hourly production monitoring based on cycle time ...
3 Opening(s)
3.0 Year(s) To 5.0 Year(s)
3.00 LPA TO 4.50 LPA
Must be Good knowledge of Mould Loading Unloding
Production Process
To control the various parameter of Moulding Machine.
To control the various problem in Moulding part.
Manpower handle and production planning.
Maintain 3R on shop floor
Maintain 5s activities.
Mould unload/loading.
Maintain 4M on shop floor.
Root cause analysis & problem solving of defects such as short shots, flash, ...
2 Opening(s)
3.0 Year(s) To 5.0 Year(s)
2.10 LPA TO 3.00 LPA
experience in Utility & Maintenance of Die casting and Injection moulding machine maintenance, D.G. Set, Operation & maintenance of 33KV/11KV Grid Substation, T/F, Servo Stabilizer, ACs, Circuit Breakers,Chillar, A.H.U. , AC & DC Drives Motors, & pumps.
Operation & Maintenance of 33/11KV Grid sub-station, O & M of Power and Distribution ...
1 Opening(s)
1.0 Year(s) To 4.0 Year(s)
1.50 LPA TO 1.80 LPA
- Diploma in mechanical, Electrical with 1 to 4 yrs experience in injection mold / rubber molding machine maintenance. - To carry out preventive and break down maintenance of injection molding machines. - To work closely with the Production team in reducing machine idle time.- Experience in hydraulic and pneumatic ...
2 Opening(s)
10.0 Year(s) To 10.0 Year(s)
4.80 LPA TO 4.80 LPA
JOB DESCRIPTION :
Shift In charge
Male
2
10 to 10
12th
Expert knowledge of injection molding process
Role Production Manager / Supervisor
Industry Type Petrochemical / Plastics / Rubber
Department Production, Manufacturing & Engineering
Employment Type Full Time, Permanent
Role Category Operations, Maintenance & Support
Education
UG :12th in Any Specialization, Other Graduate
Key Skills
Injection Molding Machine Shift Management
Maintenance
Skills highlighted with ‘‘ are preferred key skills
About Company:
Printing ink , Manufacturing ...
5 Opening(s)
3.0 Year(s) To 6.0 Year(s)
5.00 LPA TO 7.00 LPA
Sr. No
Vacancy
Department
Experience Years
Candidate Preferred
Qualification
CTC (Max )
No. Of Positions
Location
Expertise
1
Sr. Tender Executive
Sales
03 to 04
Siemens PLC
BE - IC/EC/Elec.
50,000
1
Odhav
Industrial Automation
2
Sr. Sales / Sales Engineer
Sales
03 to 04
Siemens, Delta, Sick, Murr, Lapp Kable etc
BE - IC/EC/Elec.
50,000
4
Odhav
Industrial Automation
3
Sr. Sales / Sales Engineer
Sales
02 to 03
Cable
Any Graduate
35, 000
1
Odhav
Industrial Cable
4
Sr. Sales / Sales Engineer
Sales
05 to 07
Hydraulic/ injection moulding machine
BE - IC/EC/Elec.
50000
1
Odhav
Industrial ...
2 Opening(s)
2.0 Year(s) To 10.0 Year(s)
2.00 LPA TO 4.00 LPA
Should able to perform and supervise following routine tests of general chemical nature:-
Acidic/Alkaline strength of various solutions
Preparation of solutions for standardization
To find metal content such as copper, iron etc. of powders
To perform all tests on water i.e. pH, TDS, TSS, harnesses, alkalinity, BOD, COD etc.
Should have very good knowledge of ...
4 Opening(s)
0 To 0
Not Disclosed by Recruiter
Location - Pune Qualification – Diploma, Electrical, Electronics, Mechanical Position – Diploma Trainee Experience – 0 to 1 yrs. Stipend- 21200 (PF & ESIC) and traveling allowance. Job Description and Responsibilities:
· Candidate has to work in 3 shifts.
.Candidate has to work in CNC Department.
or
.Candidate has to work on Injection Moulding Machine ...
1 Opening(s)
8.0 Year(s) To 12.0 Year(s)
Not Disclosed by Recruiter
Duties and responsibilities
Design of Plastic & Rubber Injection Molds
Knowledge in DFMA, GD&T, RPT & FMEA.
Part Feasibilities report.
Mold flow Analysis.
Carryout Moldflow Analysis for various parts & to support the Product and Tooling team
Part Design optimization to reduce War-page to improve strength & stability during New product development.
Determine number & location of ...